Description
Check the specifications, dimensions, variation details, referenced part numbers, and available fitment evidence before matching this item to an application.
| Vehicle Service Type | Mountain Bike |
|---|---|
| Color | Black |
| Brand | Yosoo Health Gear |
| Material | Plastic |
| Number of Items | 2 |
| Manufacturer | Yosoo Health Gear |
| Package Dimensions | 6.4 x 4.5 x 2.1 inches |
| Item Weight | 9.2 ounces |
| ASIN | B085LGB757 |
| Country of Origin | China |
| Customer Reviews |
4.3 4.3 out of 5 stars 23 ratings 4.3 out of 5 stars |
| Best Sellers Rank |
|
Specifications:
Material: Plastic
Color: Black
Input Voltage: 12V
Power: 12W-24W Adjustable
Temperature: maximum Temperature 70℃, Minimum Temperature 50℃
Length: 123mm/4.8″
Hole Diameter: 22mm/0.87″
Package Weight: approx. 250g
Fitment: Fit for most 12V motorcycle with 22mm(7/8″) diameter handlebar
How To Use:
[1] Remove the original handlebar
[2] Wet the inner hole of the left handlebar with soapy water, and the twisting amplitude should not be too large during installation
[3] When installing the balance iron on the left handlebar, adjust the position of the balance iron to be slightly separated from the handlebar, and do not squeeze the handlebar when tightening the screw
[4] In use, if the left handlebar slides on a steel pipe, remove the balance iron, and fix it with a few drops of glue from the end of the handlebar
[5] Power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole (not reversed)
[6] When installing the left handlebar, the power cord should be left enough for rotation
Package Included:
1 * Pair of Motorcycle Handlebar
J Karl Monaghan –
Product was unsuitable for application required and is being returned
Lessard –
Sur un vtt une poignée cherchait à sortir et j’ai corrigé sa en mettant une paille entre les deux
Rusted Diamonds –
Keeps my hands warm !
Guy –
Chauffe très bien reste à voir la durabilité
Anonymous_ –
Works really well, installed on my tail light feed. Main caveats to know is it doesn’t come with sufficient electrical connection hardware so you’ll need some connectors and a wire stripper, shrink tubing, electrical tape, and some zip ties to keep it clean .Also you’ll likely need to tune the throttle freeplay not just the fine tune up by the handle bars, but down on the throttle body. Pretty basic works, but be sure to do it before you re assemble the bike/fairings.EDIT: turns out my bike (2016 yamaha R3) Does not have this 2nd adjustment that some bikes do have. Therefore I cannot get the freeplay out of my throttle and am going to have to remove this part. Be absolutely certain you have a throttle freeplay adjustment on your throttle body (not just the fine adjustment on the cable) or you may face excess slack and it wont work
Chico –
je les ai retourner
micah mccleary –
Motorcycle grips A little bit too big but fit my wife’s just fine good quality as well not cheap material
Matt –
These get warm enough on settings 1 or 2 of 4. Only the ends of my thumbs are really cold on the freeway at 40 deg F.I chose these because the control is integrated with the grip -no big ugly switch.The left grip was difficult to slide before using a block of wood with a small hole to seal a compressed air nozzle. It was fine without adhesive and I retained the factory bar ends by removing the plastic plugs from the new grips.Wiring was easy except for routing though the plastics of this machine. For this Silverwing FSC600, I found an unused switched power pin in the fuse panel. After extending the wire, pushing it up through the fuse block, soldering it to one side of a fuse, I simply installed fuse. -clean, protected install without fear of battery drain.
daniel jaramillo –
The media could not be loaded.